PIC16C54C-04I/P【PDF 40/194 页】IC MCU OTP 512X12 18DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3886

36页 37页 38页 39页 [40页]41页 42页 43页 44页

PIC18F2450/4450

DS39760A-page 132

Advance Information

2006 Microchip Technology Inc.

There are 6 signals from the module to communicate

with and control an external transceiver:

VM: Input from the single-ended D- line

VP: Input from the single-ended D+ line

RCV: Input from the differential receiver

VMO: Output to the differential line driver

VPO: Output to the differential line driver

UOE: Output enable

The VPO and VMO signals are outputs from the SIE to

the external transceiver. The RCV signal is the output

from the external transceiver to the SIE; it represents

the differential signals from the serial bus translated

into a single pulse train. The VM and VP signals are

used to report conditions on the serial bus to the SIE

that can’t be captured with the RCV signal. The

combinations of states of these signals and their

interpretation are listed in Table 14-1 and Table 14-2.

REGISTER 14-2:

UCFG: USB CONFIGURATION REGISTER

R/W-0

U-0

R/W-0

UTEYE

UOEMON(1)

—

UPUEN(2,3)

UTRDIS(2)

FSEN(2)

PPB1

PPB0

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 7

UTEYE: USB Eye Pattern Test Enable bit

= Eye pattern test enabled

= Eye pattern test disabled

bit 6

UOEMON: USB OE Monitor Enable bit(1)

=UOE signal active; it indicates intervals during which the D+/D- lines are driving

=UOE signal inactive

bit 5

Unimplemented: Read as ‘0’

bit 4

UPUEN: USB On-Chip Pull-up Enable bit(2,3)

= On-chip pull-up enabled (pull-up on D+ with FSEN = 1 or D- with FSEN = 0)

= On-chip pull-up disabled

bit 3

UTRDIS: On-Chip Transceiver Disable bit(2)

= On-chip transceiver disabled; digital transceiver interface enabled

= On-chip transceiver active

bit 2

FSEN: Full-Speed Enable bit(2)

= Full-speed device: controls transceiver edge rates; requires input clock at 48 MHz

= Low-speed device: controls transceiver edge rates; requires input clock at 6 MHz

bit 1-0

PPB1:PPB0: Ping-Pong Buffers Configuration bits

= Enabled for all endpoints except Endpoint 0

= Even/Odd ping-pong buffers enabled for all endpoints

= Even/Odd ping-pong buffer enabled for OUT Endpoint 0

= Even/Odd ping-pong buffers disabled

Note 1:

If UTRDIS is set, the UOE signal will be active independent of the UOEMON bit setting.

The UPUEN, UTRDIS and FSEN bits should never be changed while the USB module is enabled. These

values must be preconfigured prior to enabling the module.

This bit is only valid when the on-chip transceiver is active (UTRDIS = 0); otherwise, it is ignored.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式